El Mandadero - Last Mile Delivery Robot
  • What is El Mandadero?
  • Guides
    • ELM4 Assembly Guides
      • Bottom Chassis Assembly ELM4 200-000
        • ELM4 230-000 T-Arm Full Assembly
          • 3D Printed Parts for Torsion Arm Suspension
        • T-Arm Insertion to Bottom Chassis
        • Accessories installation
          • 3D Printed files for Accessories
        • Cross Braces and Grommets Installation
      • Top Chassis Assembly ELM4 100-000
        • Inner Structure Assembly
        • Top Doors Assembly
        • Arch Assembly ELM4 300-000
          • 3D Printed Parts for Arch Assembly
        • Arch and accesories installation
          • 3D Printed files for Top Chassis Accessories
      • ELM4 Battery Pack Assembly
        • 3D Printed Battery Pack Components
      • ELM4 Full Assembly Guide
    • ELM4 Electronics Guides
      • System's power supply
      • Remote Kill Switch
      • BMS771
    • VESC configuration
    • Manufacturing Guides
      • Welded Torsion Arm
      • Welded Torsion Box
      • Square Axle sub-assembly
      • Torsion arm PolyUrethane
    • xxxAdvanced permissions
  • Fundamentals
    • xxxProjects
    • xxxMembers
    • xxxTask Lists
    • xxxTasks
  • Use Cases
    • xxxFor Designers
      • Figma Integration
    • xxxFor Engineers
      • GitHub Integration
    • xxxFor Support
      • Intercom Integration
  • Extras
    • xxxKeyboard Shortcuts
Powered by GitBook
Page cover
On this page
  1. Guides
  2. ELM4 Assembly Guides
  3. Top Chassis Assembly ELM4 100-000

Arch Assembly ELM4 300-000

Assembly guides showing the Archway module assembly and its installation in the Top Payload.

PreviousTop Doors AssemblyNext3D Printed Parts for Arch Assembly

Last updated 2 years ago

CtrlK
  • Video
  • Bill of materials
  • Procedure
  • Assembly notes

Video

Bill of materials

Procedure

  1. Grab the Inner Brackets and Install the Reinforcement Gussets as so.

    Use two M3-0.5x5 button head cap screws
  2. Take the Top Inner Bracket and install it on the two pre-assembled Inner Brackets.

    For this you will need four M3-0.5x5 screws and four M3-0.5x8 screws. The latter will go to the reinforcement gussets.
  3. Install the top lights using four 12mm M3 socket head cap screws.

    Inner view
  4. If you are using the RC050 screen, install the plastic adapter in the inner bracket and then install the screen. For this you will need four screws for the screen and four for the bracket, all being M3-0.5x5 bottom heads.

  5. For the DIS79340P screen just install it directly into the Inner Brackets using four M3-0.5x5 screws.

  6. Now install the Top Cover using four M3-0.5x5 screws.

  7. Assemble the angled LED lights in the Side Covers as shown.

  8. Now install the side covers using six M3-0.5x5 screws per cover.

Assembly notes

  • You can use both of the screens with their peripherals facing either up or down. For the RC050 screen the plastic adapter includes a double set of holes to center the screen to either orientation.

  • After installing the screens, steps 6 and 8 can come in either way, whether you install the side covers first or the top cover. Just make sure the side covers have the LED lights installed before putting the top cover in place.

  • There is a side cover model for each screen variation.

Outer view
Make sure to install the bracket with the arrow facing up for a correct alignment.